Re: Creo View popping up 3D Connexion Properties Window?
I tried it with creo view express and I don't have any problems. I also don't have any problems with Creo Parametric. I don't think I have Creo View installed, just express. What Creo build are you...
View ArticleRe: Creo View popping up 3D Connexion Properties Window?
We're using Creo View 2.0 and 3.0 in Express and MCAD versions. It happens in both whenever you right-click on a component and select Open in new view. 3D Connexion version 10.0.22
View ArticleRe: Creo View popping up 3D Connexion Properties Window?
Right clicked and opened in new view and nothing pops up for me. Creo View Express 2.0 M040 build 15Device: SpacePilotDriver Version: 6.16.1
View ArticleRe: Creo View popping up 3D Connexion Properties Window?
Yeah, I wish I could. Did you ever figure out a solution to the composite layups in Creo? Just curious.
View ArticleRe: Creo View popping up 3D Connexion Properties Window?
Nope, we abandoned it and our composites engineer went back to using Catia
View ArticleRe: Creo View popping up 3D Connexion Properties Window?
Interesting. We are looking into Fibersim but currently do everything by hand in Creo. I hear Catia is much better in these regards.
View ArticleRe: x value at which the function is max, and the maximum function value
So its as I suspectd - the value of ORIGIN in your sheet is changed from the default 0 to 1.So you have to apply the changes as given in my post above.
View ArticleRe: Creo View popping up 3D Connexion Properties Window?
FiberSim has an interface with Catia and NX so users can work directly in the native tool. They've approached PTC about developing the same, but have gotten no interest. Here's the full...
View ArticleClik here to view.
Re: Assembly to step file
When attempting to open the STEP assembly in another software, does the software have the capability to open STEP assemblies as shown below with Creo? If you don't import it as an assembly, you might...
View ArticleRe: Rigid/flex CCA modeling
We have modelled a few rigid-flex pcbs and we are still developing the process but we do it as follows:-The flexible "core" (around 0.3 mm) is modelled with a sheetmetal part. It can be created as...
View ArticleRe: How to extract the fundamental component from a discrete data
Maybe this link can be helpful http://communities.ptc.com/message/212019#212019
View ArticleRe: Helping solving this problem symbolically in Prime 3.0
Solve what? BTW, if you define a1(r):=... and then e(r):=... you have to write a1(r) etc. on the RHS of the assignment, too. This applies to all of your function definitions.
View ArticleRe: Rigid/flex CCA modeling
Thanks for the detailed reply, Carlos. I suspected this was the case. Good to see someone has refined the process to the level you have.
View ArticleRe: how to save calculated data for later use so that Mathcad does not...
Here is your demo file rewritten without using a single symbolic evaluation. I am sure it could be further streamlined and simplified - I simply strictly followed your sheet line by line. The plot now...
View ArticleWho's going to the 2014 Championship in St. Louis?
I'll be at this year's championship with FRC Team 1671 and Team 5134.Anybody else from the community going? Scott, Sheila, Shannon?
View ArticleClik here to view.
Re: How to create curve profile in proe
Haris, Would you like to create sketch as displyed in image or part? Part in image can be created by one sketch using Circles (+Trim) or Arcs (depends on individuals). Reference part attached.
View ArticleRe: Derivative of function
The error message "These values cannot be compared" is misleading unfortunately. The real reason, as Mike and Alan already pointed out, is, that getting the extrema by setting the first derivative to...
View Article