Re: Creo3 fasteners & 'carries shear'
Agreed, springs aren't the same. Mind you, everything is an approximation and in my case, carrying shear is not good. I thought the change over was with the intro of Creo1.0
View ArticleRe: PTC Creo 3.0 Now Available!
Chris,I found the More tab in sketcher thanks. Why was a new tab created rather than moving them into the sketcher drop-down? I restored the ui file to the text folder but the Schools tab doesn't...
View ArticleRe: Which 3 button mouse do you recommend?
I ended up with the 4 wired. After using it for a few days I replaced my keyboard with a mini keyboard. I found with the Evoluent my right hand needed to travel too far. Wish I could have afforded a...
View ArticleRe: Creo 2.0 Student-Version doesn´t open
Ok, everytime the window opens this warning appears: Warning: Proper TCP/IP configuration was not detected The TCP/IP protocol is not installed or configured properly.
View ArticleRe: Given/Find "this variable is undefined"
hey guys thanks a million. you both are right. gotta admit im kinda new using mathcad to solve themodynamics problems, i usually use a couple of special excelsheets to solve them, but in this case...
View ArticleRe: Given/Find "this variable is undefined"
You have assigned the results of the solve block to the vector "solucion" and not to the variables used for the calculation. So they still are assigned the guess values.You either have to assign a...
View ArticleClik here to view.
Re: Given/Find "this variable is undefined"
There are at least two problems in your sheet. The most prominent one is a simple typo you can quickly find using "Trace error" as Alan had shown:The system still will not solve after you delete that...
View ArticleRe: is it possible to track "b-graph" on "a-graph"
I don't know what you mean by "track one graph on another". Do you mean plot the ordinate values of b vs the ordinate values of a?
View ArticleRe: IsoDraw 7.1 and Windows 8
As I look at the PTC/Arbortext IsoDraw 7.2/7.3 platform support, Windows 8 is supported by IsoDraw 7.3 M030. IsoDraw 7.3 M030 is run as a 32-bit application.IsoDraw 7.1 does not support Windows 8 See...
View ArticleClik here to view.
Re: Optimizing (max / min) of a function in terms of parameters given:
You may use a program with a local functiin definition:
View ArticleClik here to view.
Re: Optimizing (max / min) of a function in terms of parameters given:
In Mathcad 15 this is simple:But I guess they broke it in Prime
View ArticleRe: PTC Creo not retaining dimension values?
This is not normal behavior. The only time I see this kind of rounding is when the value is used in a different dialog. I do find this behavior troubling when this does happened, but it does not...
View ArticleClik here to view.
Clik here to view.
Re: PTC Creo not retaining dimension values?
Here is an example of a "ribbon dim" change... compared to a section dim.The .6667 was entered as 2/3. The value only takes on the value of the number of places designated.Unlike the dimension added...
View ArticleRe: Performance when optimizing program blocks
Eher. Tanks for the exhaustive answer. unfortunately I was referring to Programm Blocks, Not equations.
View ArticleClik here to view.
Re: Sort by...then by....
N M wrote: With some slight modifications it should be possible using recursion to sort for as many columns as demanded.I have been trying to figure out how to do this but can't get my head around it....
View ArticleRe: Mathcad Express Installer No applications to Select
Selecting "install" in the bottom right, results in 0 software installed. It installs what was selected, in this case no software. A quick check of the programs folder also shows 0 installed and the...
View ArticleRe: Timezone Issue
Rahul, This is just a guess, but is the descrepency shown in Time Zone 2 (GMT-05:00) only appear on when the start or end date is a Friday or a Monday?
View Article