Creo equivalent of SolidWorks configurations in parts?
Hi there, I've been with a new company using Creo 2.0 for the last three months and we would really benefit from being able to create parts with what I know as "configurations": I'm not sure what the...
View ArticleRe: Windchill 10.1 WGM Creo 2 compare status
Carl, we added the additonal status columns to our default workspace view and create some new table views without the status icons. By default I understand they are not displayed because it results...
View ArticleRe: Creo equivalent of SolidWorks configurations in parts?
Hi Andy, Family table in Creo Parametric is as Configuration in Solidworks and to use that functionality: 1. Create the part as sketch you attached.2. Select Tools > Family Table3....
View ArticleRe: Model with simple frustrum - volume calculation wrong
I think Creo is right. I'm not sure where the formula came from but ... L = l_base - ((l_base-l_top)/delta_z) * Z W = w_base - ((w_base-w_top)/delta_z) * Z A = L * W = l_base*w_base-...
View ArticleRe: Exclusion of a component
Are you looking for displacement in the Y direction for the entire assembly?
View ArticleRe: Model with simple frustrum - volume calculation wrong
I should be able to simplify the integral to be the same as the original formula, but so far no luck. I looked at the Wikipedia page that showed the derivation of the original formula, but it doesn't...
View ArticleRe: Model with simple frustrum - volume calculation wrong
I got the original formula from the CRC math tables. A handy book from olden times which has all sorts of nice answers to unusual geometry questions. It's an odd conundrum. One would, reasonably,...
View ArticleClik here to view.
Re: Helical Sweep, Ball and Worm Gear Assembly
You guys are tough to please But of course you are right. Anyone have the formula handy for the proper spacing using the helix parameters?
View ArticleClik here to view.
Re: Helical Sweep, Ball and Worm Gear Assembly
This can be done at the lead-screw level and maintained with relations. As far as I can tell, this is correct and fully parametric.Funny thing is, I can change the 12.0 and nothing updates until I exit...
View ArticleRe: mechanism in fuel injector(mdx & mdo)
Regardless of what it happening in the specification, the mechanism is a simulation of some sort.If you have a "servo motor" that you are tracking the RPM, then you are asking for a trigger. I am not...
View ArticleHow to create clockwise rotation of shaft in pro e maecahnism
In my case I have assigned pin for the shaft & later defined force motor for the same. But If i run the analysis the shaft is rotating clock & anti clockwise .How to control, only it should run...
View ArticleRe: How to create clockwise rotation of shaft in pro e maecahnism
You probably have a motor profile defined that does this, such as a sine profile in conjunction with position. There are many ways to control a motor's motion. Typically I find that I have to use...
View ArticleRe: tracing the edge of a cutting tool (toolpath)
I have played around with that problem a little bit (still not implemented an outline algorithm) and thought I would post that intermediate result in case somebody else would like to give it a try...
View ArticleMultiple versions of the same part
HiCreo keeps in my memory, multiple versions of the same part.Example:123.PRT.1123.PRT.2123.PRT.3It is really annoying and takes up a lot of memory space. How can you disable it?
View ArticleRe: Multiple versions of the same part
This is normal procedure for saved parts. There will be occasions when you will be very thankful that this is the case. However, periodic maintenance will take care of this. There is a "purge.bat"...
View ArticleRe: Multiple versions of the same part
Thanks for the reply "Sometimes it required some help setting this up to function, but it has been part of Pro|E since the beginning." Can you explain more how I can check the settings? "You can also...
View ArticleRe: Helical Sweep, Ball and Worm Gear Assembly
Good idea, this would be sorta like a driving model or skeleton model of the assembly, cause it really seems like you can project to whole thing into 2D, and drive it from there. The sketch could be...
View Articlewelding
i am having a student edition of creo 2.0 parametric. i wanna do welding , but the welding option provided in the application tab is not getting executed when i click on it.
View ArticleRe: What type of association has to be used for 2D drawing?
In the preferences, out of the box the attributes to carry through to the WTPart is set to *. However, I had a PTC ticket that said I could remove the * from that preference (effectively making it...
View ArticleClik here to view.
How to write a Cumulative distribution function
Hi, I'm beginner. How can I write a function like this , and then make a plot? Thank you.
View Article